Glue

OaseFol SprayBond 500 ml

The OaseFol SprayBond 500 ml is a practical contact adhesive for attaching EPDM liner to various surfaces, such as wood and masonry. The spray adhesive is suitable for use with OaseFol EPDM liner and EuroFol EPDM liner and provides convenient installation support when creating a pond. Especially with steep pond walls, SprayBond makes it easier to hold the liner in place and work it neatly.

Thanks to the convenient 500 ml spray can, the adhesive can be applied evenly to both the EPDM liner and the surface. After a short drying time of approximately 2 to 4 minutes, both surfaces can be bonded together.

Convenient installation support for EPDM pond liner

Installing EPDM liner is generally relatively easy on a flat pond bottom. However, working the liner can become more difficult on steep or vertical pond walls. The liner can shift or sag during installation, making it harder to position neatly.

OaseFol SprayBond offers a practical solution for this. By temporarily and securely attaching the EPDM liner to the surface, it stays better in place during the further construction of the pond. This makes the contact adhesive particularly suitable for ponds with steep walls, height differences, or surfaces that are difficult to line.

Suitable for various surfaces

OaseFol SprayBond can be used to attach EPDM liner to various suitable surfaces, including wood and masonry. This makes the adhesive widely applicable to a variety of pond constructions.

For a good bond, it is important that the surface is prepared correctly. All surfaces to which the adhesive is applied must be dry, grease-free, and dust-free. A properly prepared surface contributes to the correct application of the contact adhesive.

Suitable for OaseFol and EuroFol EPDM liner

SprayBond is suitable for use in combination with:

• OaseFol EPDM liner
• EuroFol EPDM liner

This means the contact adhesive can be used as part of a complete EPDM pond construction. The adhesive is primarily intended as installation support in situations where the liner needs to be attached to a surface while being laid.

Easy application with the spray can

The 500 ml spray can makes applying OaseFol SprayBond easy. Because the adhesive is sprayed, it can be practically distributed over the desired surface without the need for a separate brush or roller.

For bonding, both the EPDM liner and the surface are sprayed with SprayBond. The adhesive must then dry for approximately 2 to 4 minutes. After that, the liner and the surface can be bonded together.

By spraying both surfaces, the contact required to secure the liner in the desired position is created.

Consumption of approximately 70 ml per m²

The stated material consumption is approximately 70 ml per m². With a capacity of 500 ml, you will have enough adhesive for various installation tasks. Actual consumption may vary in practice depending on factors such as the surface, the application, and the method by which the adhesive is applied.

For larger surfaces, it is therefore advisable to determine in advance approximately how much SprayBond is needed.

Ideal for steep pond walls

One of the most important applications of OaseFol SprayBond is laying liner against steep pond walls. In such constructions, the weight of the liner can cause it to sag during installation.

By securing the liner to the surface with SprayBond, installation becomes considerably easier. You can position the liner more accurately and hold it in place while continuing with the construction of the pond.

This makes the contact adhesive suitable not only for complete pond projects but also for specific sections of a pond where extra support is desired while installing the liner.

Surface preparation

Good preparation is important before you start bonding. Therefore, first check that both the EPDM liner and the surface are suitable for working.

The surface must be:

• Dry
• Dust-free
• Free of grease and other contaminants

Then spray both the liner and the surface to which it will be attached. Allow for the stated drying time of 2 to 4 minutes before bringing both surfaces together.

Benefits of OaseFol SprayBond

• Contact adhesive for attaching EPDM liner
• Suitable for OaseFol EPDM liner
• Suitable for EuroFol EPDM liner
• Bonds EPDM liner to surfaces such as wood and masonry
• Ideal as installation support for steep pond walls
• Practical spray can for easy application
• Applied to both the liner and the surface
• Short drying time of approximately 2 to 4 minutes
• Material consumption of approximately 70 ml per m²
• Capacity of 500 ml
• Helps hold the liner in the desired position during installation

Specifications

Brand: Oase
Product: OaseFol SprayBond
Product type: Contact adhesive / spray adhesive for EPDM liner
Capacity: 500 ml
Suitable for: OaseFol EPDM liner and EuroFol EPDM liner
Application: Attaching EPDM liner to various surfaces
Suitable surfaces: Including wood and masonry
Drying time for bonding: approx. 2 to 4 minutes
Material consumption: approx. 70 ml per m²
Packaging: Spray can
Surface: Dry, grease-free, and dust-free

Easier and more accurate placement of EPDM liner

With the OaseFol SprayBond 500 ml, attaching and positioning EPDM pond liner becomes much easier. The contact adhesive is particularly useful for steep pond walls, where liner can be difficult to keep in place during installation.

Thanks to the practical spray can, the adhesive can be easily applied to both the liner and the surface. After a drying time of approximately 2 to 4 minutes, both surfaces can be bonded together. This makes OaseFol SprayBond a practical installation aid for neatly working in OaseFol and EuroFol EPDM pond liner.

OaseFol SeamTape 30.5 m x 7.62 cm

The OaseFol SeamTape is a high-quality, wear-resistant seam tape for reliably joining OaseFol EPDM pond liner. With a generous length of 30.5 metres and a width of 7.62 cm, this tape is ideal for creating strong, durable liner connections when installing or repairing a pond.

Thanks to its vulcanised design, the SeamTape is particularly tear-resistant, flexible and durable. This allows the tape to work well with the flexible properties of EPDM liner, creating a reliable connection between different liner sections.

Reliably joining EPDM pond liner

For larger ponds, it may be necessary to join several sections of pond liner together. A correct and secure seam connection is essential in this case. OaseFol SeamTape is specially designed to create such connections between OaseFol EPDM liner sections.

The tape is applied between the overlapping liner sections and, when installed correctly, creates a strong connection. This allows you to join different pieces of liner to the desired size for your pond project.

SeamTape can also play an important role in repair or modification work on existing EPDM liner.

Vulcanised for extra durability

A key feature of the OaseFol SeamTape is its vulcanised design. This gives the material excellent mechanical properties. The tape is tear-resistant, flexible and wear-resistant, properties that are important when working with flexible EPDM pond liner.

EPDM liner can move slightly under the influence of temperature and stress. A liner connection must be able to accommodate this movement without immediately losing its functionality. The flexibility of the SeamTape makes the tape particularly suitable for this application.

For use with OaseFol EPDM liner

OaseFol SeamTape is designed for use with OaseFol EPDM liner. By combining the different components of the OaseFol system, seams and connections can be carefully constructed.

For a good bond, proper preparation of the liner surface is important. OaseFol Primer can be used for this purpose. The primer cleans and activates the surface of the EPDM liner before the SeamTape is applied.

The primer, EPDM liner and SeamTape thus form a practical system for creating liner connections.

Generous 30.5-metre roll

The OaseFol SeamTape is supplied on a roll measuring no less than 30.5 metres long. This provides enough material for creating multiple or longer seams.

With a width of 7.62 cm, the tape provides a generous contact area between the different liner sections. This makes the tape suitable for both smaller jobs and larger pond projects where multiple pieces of liner need to be joined together.

Suitable for installation and repair

The SeamTape can be used when installing a new liner pond, for example when a single piece of EPDM liner is not large enough to cover the entire pond surface.

The tape is also practical for work on an existing liner pond. When liner needs to be modified or a new liner connection needs to be made, the SeamTape offers a solution within the OaseFol system.

Correct preparation is important

For a durable connection, it is important that the EPDM liner is carefully prepared before the SeamTape is applied. The liner surface must be suitable for bonding and free from conditions that could prevent a good bond.

Use the dedicated OaseFol Primer for this purpose and follow Oase's processing instructions when applying the SeamTape. Careful preparation and application are essential for the quality of the final liner connection.

Benefits of OaseFol SeamTape

• Specially designed for joining OaseFol EPDM liner
• Strong and wear-resistant seam tape
• Vulcanised design
• Highly tear-resistant
• Flexible and pliable
• Suitable for durable liner connections
• Can be used for installation and repair work
• Generous roll length of 30.5 metres
• Width of 7.62 cm
• Can be combined with OaseFol Primer

Specifications

Brand: Oase
Product: OaseFol SeamTape
Product type: Seam tape for EPDM liner
Length: 30.5 metres
Width: 7.62 cm
Design: Vulcanised
Properties: Tear-resistant, flexible, wear-resistant and durable
Application: Joining EPDM pond liner
Suitable for: OaseFol EPDM liner
Recommended pre-treatment: OaseFol Primer

Strong connection for OaseFol EPDM liner

With the OaseFol SeamTape 30.5 m x 7.62 cm, you have a strong and flexible seam tape for professionally joining OaseFol EPDM pond liner. The combination of high tear resistance, flexibility and a wear-resistant design makes the SeamTape excellently suited for durable liner connections.

In combination with proper preparation and OaseFol Primer, this SeamTape forms an important component when installing, joining or modifying EPDM pond liner.

OaseFol Primer 0.75 Litre

The OaseFol Primer 0.75 Litre has been specially developed for preparing and activating EPDM pond liner before OaseFol SeamTape or OaseFol Flashing is applied. Proper pre-treatment is essential for a reliable bond when gluing liner sections together and carrying out repairs.

The primer cleans and activates the surface of the EPDM liner, optimally preparing it for further processing. OaseFol Primer is suitable for both OaseFol EPDM liner and EuroFol EPDM liner, making it an important component in professional liner bonding.

Optimal preparation of EPDM liner

When bonding or repairing EPDM liner, a properly prepared surface is of great importance. Contaminants and an insufficiently activated surface can affect the adhesion of the tape or flashing used.

OaseFol Primer is applied to the relevant liner surface before applying the SeamTape or Flashing. This cleans and activates the surface, making it ready for the next step in the processing procedure.

For bonding and repairing pond liner

The primer is suitable for various tasks involving EPDM pond liner. It can be used when two pieces of liner need to be bonded together, but also when existing liner needs to be repaired.

In combination with OaseFol SeamTape, the primer can be used for creating liner bonds and seams. For tasks involving OaseFol Flashing, the primer also provides the necessary surface preparation.

This makes the product suitable for both installing a new liner pond and carrying out maintenance and repair work on existing EPDM liner.

Suitable for OaseFol and EuroFol EPDM

OaseFol Primer was developed for use in combination with:

• OaseFol EPDM liner
• EuroFol EPDM liner
• OaseFol SeamTape
• OaseFol Flashing

By using products designed to work together, the entire liner bond can be constructed according to the intended system.

Consumption of OaseFol Primer

One package contains 0.75 litres of primer. The stated material consumption is approximately 20 linear metres of seam per litre of OaseFol Primer.

Actual consumption may depend on the application and the way the product is applied. Always ensure that the entire surface on which the tape or flashing is applied is correctly prepared during processing.

Application

Before you start, ensure that the relevant section of the EPDM liner is suitable for further processing. Then apply OaseFol Primer to the area where SeamTape or Flashing will later be placed.

After pre-treatment, the relevant bond or repair can be further finished with the appropriate OaseFol product. Always follow the corresponding Oase processing instructions during application.

Benefits of OaseFol Primer

• Pre-treatment for EPDM pond liner
• Cleans and activates the liner surface
• For use before applying OaseFol SeamTape and Flashing
• Suitable for OaseFol EPDM liner
• Suitable for EuroFol EPDM liner
• Ideal for liner bonds and repair work
• Volume of 0.75 litres
• Material consumption of approximately 20 linear metres of seam per litre
• Part of the OaseFol liner system
• Suitable for professional processing of EPDM pond liner

Specifications

Brand: Oase
Product: OaseFol Primer
Volume: 0.75 litres
Application: Pre-treatment and activation of EPDM liner
Suitable for: OaseFol EPDM and EuroFol EPDM
Can be used with: OaseFol SeamTape and OaseFol Flashing
Material consumption: approx. 20 linear metres of seam per litre
Shelf life: 12 months

Proper preparation for a reliable liner bond

With the OaseFol Primer 0.75 Litre, you prepare OaseFol and EuroFol EPDM pond liner for the application of SeamTape or Flashing. The primer cleans and activates the surface and is therefore an important preparatory step when creating liner bonds or carrying out repairs.

Whether you want to bond different pieces of EPDM liner together during installation or repair an existing pond liner: with OaseFol Primer, you ensure that the liner surface is correctly prepared for further processing.

The AquaKing MS Sealer is a high-quality adhesive and sealing compound specially developed for use in and around ponds. This versatile sealer provides a strong, durable, and watertight bond between materials such as PVC, EPDM, liner, stone, metal, and plastic.

The MS Sealer is free from silicone and solvents, making it safe to use in ponds with fish and plants. The compound remains permanently flexible, does not crack, and is resistant to UV radiation, weather conditions, and aging.

Thanks to its strong adhesion, the AquaKing MS Sealer can be used for sealing seams, leaks, pipe penetrations, and connections in PVC pipes or pond liners. The compound can be applied both underwater and to damp surfaces.

Application:

• Bonding and sealing PVC, liners, stone, and plastic

• Repairing pond liners or pipes

• Sealing pipe penetrations, seams, and leaks

• Suitable for use above and below water

Benefits:

• Remains permanently flexible and watertight

• Strong adhesion, even to damp surfaces

• Weather- and UV-resistant

• Safe for fish and plants

Specifications:

• Contents: 290 ml

• Color: black (also available in gray/white, depending on stock)

• Application: indoor and outdoor

• Type: MS polymer sealing compound

• Brand: AquaKing

In short: the AquaKing MS Sealer is the ideal solution for permanently bonding and sealing pond liners, PVC, and other materials – watertight, flexible, and reliable.

The Griffon WDF-05 PVC adhesive 500 ml is a high-quality, fast-drying, thixotropic (non-drip) adhesive with a blue color, specially developed for bonding hard PVC pipes, sleeves, and fittings in both pressure and drainage systems. Thanks to its gap-filling properties, this adhesive is extremely suitable for applications with both tight and loose fits.

The Griffon UNI-100 Hard PVC Solvent Cement (500 ml) is a high-quality, fast-drying adhesive specially developed for bonding hard PVC pipes, couplings, and fittings in both pressure and drainage systems. Thanks to its gap-filling and thixotropic properties, this adhesive is suitable for applications with both tight and loose fits.

OASE PVC liner adhesive is specially suited for OASE AlfaFol PVC pond liner. The high-quality liner adhesive ensures secure bonding and fastening of liner sheets. The adhesive is simple and easy to use from the 100 ml can with an integrated brush in the lid.

• Bonds all PVC liners quickly and easily.
• Shelf life: 2 years
• For 4 m² of surface area (1000 ml)

OASE PVC liner adhesive is specially suited for OASE AlfaFol PVC pond liner. The high-quality liner adhesive ensures secure bonding and fastening of liner sheets. The adhesive is simple and easy to use from the 250 ml can with an integrated brush in the lid.

• Quickly and easily bonds all PVC liners.
• Shelf life: 2 years
• For 1 m² of surface area (250 ml)

The construction adhesive with maximum bonding strength - even underwater. The powerful UniFix+ pond liner adhesive is universally applicable, as it bonds not only OASE pond liners made of EPDM, rubber, or PVC. The enormous bonding strength is particularly effective on a wide variety of surfaces, such as stone, metal, or plastic. The adhesive cartridge contains 290 ml and must be used within one year. You can be sure: UniFix delivers on its promise.

• Strong universal adhesive for various liners and surfaces
• 290 ml cartridge

Black PUR foam, suitable for creating waterfalls, stream beds, and backgrounds in aquariums and terrariums. It dries dark, resulting in a natural appearance. With high adhesion to virtually all materials and surfaces, both porous and non-porous, such as polyester, natural stone, concrete, wood, metals, and various plastics. Scaping foam is safe for both plants and animals, provided the foam has fully cured after application.

Application: Read the safety instructions carefully before use! Ensure that the surface is dry, clean, free of grease and dust. Remove loose parts and moisten the surface beforehand. Attach the straw to the can in an upright position and shake the can vigorously at least 20 times. Hold the can upside down and spray out the foam, filling joints up to 60% and spraying multiple times for large joints. After approximately 15 minutes, the foam is tack-free; full curing can take up to 16 hours, depending on the thickness of the applied foam. Processing temperature between 5 and 25°C. Slight discoloration is possible.

Shelf life: 12 months in an unopened, upright package in a cool, frost-free, dry place (5-30°C); consult the print on the bottom. Limited shelf life after opening.

AstralPool SB-Pool Sealer – High-Quality Pool Sealing

The AstralPool SB-Pool Sealer is a premium sealing solution designed to provide long-lasting protection for swimming pools and other water features against leaks and water loss. This high-quality sealer provides a strong, watertight seal and ensures that your pool system continues to operate optimally.

Features:

• Watertight seal – Prevents leaks and protects against water loss.
• High-quality – Developed by AstralPool for maximum reliability.
• Long-lasting protection – Remains effective for a long time, even with intensive use.
• Versatile application – Suitable for various pool materials and installations.
• Easy application – Easy to apply for both professionals and DIY users.

AquaForte SuperStrong White Adhesive 290ml – Professional elastic adhesive and sealing compound for ponds and swimming pools

The AquaForte SuperStrong white adhesive 290 ml is a high-quality, elastic adhesive and sealing compound specially developed for durable applications in demanding environments such as ponds, swimming pools and water features. This versatile adhesive combines strong adhesion with lasting flexibility, making it ideal for both assembly and sealing work.

Strong and durable adhesion to virtually all materials

The SuperStrong adhesive is known for its excellent adhesion to a wide range of materials. This makes it suitable for a variety of applications inside and around ponds and swimming pools.

Suitable for, among others:

• Plastics (with the exception of PE and PP)
• Metal
• Wood
• Concrete and stone
• PVC and pond materials

After curing, the adhesive forms a strong, flexible bond that is resistant to movement, temperature differences and long-term stress.

Elastic and water-resistant for long-lasting performance

An important advantage of this adhesive is its lasting elasticity. This ensures that bonds do not crack or come loose due to material movement or changing conditions.

In addition, the adhesive is:

• Completely water-resistant
• UV-resistant
• Suitable for long-term use in wet environments

This makes the SuperStrong adhesive perfect for applications in and around water.

Versatile replacement for multiple types of adhesive

The AquaForte SuperStrong was developed as an all-in-one solution and can replace several traditional adhesives and sealants, such as:

• Assembly adhesive
• Wood glue
• PU adhesive
• Silicone sealant
• Acrylic sealant
• Butyl sealant

This makes the product particularly efficient and practical for both installations and repairs.

Overpaintable and easy to finish neatly

After curing, the adhesive is overpaintable, allowing you to easily finish it in the desired color. This ensures a clean and professional appearance, for both visible and concealed applications.

Easy to work with and apply

The adhesive is supplied in a standard 290 ml cartridge and is easy to apply with a sealant gun. Thanks to its good workability and strong initial adhesion, you can work quickly and efficiently without complex preparation.

Key features

• Color: White
• Contents: 290 ml
• Elastic and permanently flexible
• UV- and water-resistant
• Overpaintable
• Suitable for ponds, swimming pools and outdoor use
• Adheres to virtually all materials (except PE and PP)

Reliable choice for assembly and sealing

With the AquaForte SuperStrong white adhesive, you choose a powerful, versatile and durable solution for all your gluing and sealing work. Ideal for applications where reliability, flexibility and water resistance are essential.